-
The GoodWe Smart DT series inverter is specially designed for three-phase home solar systems, covering a wide power range of 5kW, 6kW,10kW, 15kW, and 20kW. The integrated two MPPTs allow two-array inputs from different roof orientations. The SDT series inverter is small, light and easy to install. Suitable for both outdoor and indoor installations, this inverter offers a quiet operation thanks to its fanless, natural convection cooling.
-
INVT Solar Pump Inverter
INVT Goodrive100-01 Variable Frequency Drive is positioned in environmental-friendly and economical PV market, the product is applicable to PV pump system, replaces water storage with electric storage and needs no battery modules. The direct current generated by solar modules is input to the inverter and then converted into the alternating current to drive various pumps directly. Additionally, the output frequency is adjustable in real time according to sunlight intensity change.Features:
1, Maximizing power generation efficiency of solar modules with the use of advanced MPPT control technology. 2, Adjusting water outflow of pumps quickly on basis of sunlight intensity change. 3, Automatic hibernation and wakeup. (i) Hibernate at high water level and wake up at low water level. (ii) Hibernate at sunrise and sunset and wake up at strong sunlight. 4, Underload protection & fault protection of water level sensor avoiding pumping off after water supply dries up. 5, TI DSP technology and Infineon PIM design, with functions of over-current, over-voltage and over temperature protection, built-in C3 filter, achieving reliable, automatic and unattended running.MPPT Intro:
MPPT controller (Maximum Power Point Tracking) can adjust the output state to make the PV cell outputs more power to the load system. PV cell and MPPT controller can effectively solve the power supply problem for the area which can’t be covered by the gird power. The output power of the PV cell is related to the working voltage of the MPPT controller. Only working at the suitable voltage, can the output power be maximum.Feel free to contact us: Mobile: 030 77 381 381
-
Feel free to contact us: Mobile: 0344 3813810
- True-RMS 1000A AC/DC
- Work in tight spots with the 18" iFlex current probe and measure up to 2500A AC
- CAT III/IV Safety ratings
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810
- CAT IV 600
- CAT III 1000 V
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810
- True-RMS
- 600 A AC/DC
- Works with iFlex flexible current probes
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810
- Detachable Jaw clamp
- Built in Flash/Torch light
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810
- CAT III Rating 600v
- Low Pass Filter
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810 The Fluke 360 leakage tester is a rugged and accurate solution for leakage current measurement. Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment – saving you time, without compromising on quality or safety. The unique jaw design of the Fluke 360 AC Leakage Current Clamp Meter eliminates the influence of adjacent current conductors, and measure leakage current down to 1 µA for monitoring of insulation and makes it ideal for checking insulation of low-voltage circuits and electrical components.. The ergonomic design of the Fluke 360 ensures easy measuring. The measuring clamp fits into tight spaces and the wide display angle clearly shows the measured value on the display after removing the clamp for the measured conductor. The Fluke 360 minimizes the effects of external magnetic fields, even at low currents. This allows you to perform accurate and reliable tests in today’s crowded electrical environments. The tough and high-quality jaw design of the Fluke 360 leakage tester guarantees high stability for long-term repeatability and durability. Why leakage current testing? Leakage currents can be an indicator of the effectiveness of insulation on conductors. High levels of leakage current may be present in circuits where either the insulation resistance is low, or electronic equipment with filters is used. Leakage currents can cause disruptions of the normal operation of equipment and installations. It is possible to locate the source of leakage currents by using the Fluke 360 leakage current clamp meter and taking methodical measurements throughout the installation. The big advantage of leakage current testing versus insulation testing is that the installation and equipment do not need to be powered down but can be done during normal operation. What’s Included:
- Soft carrying pouch
- Users manual in languages: English, French, Spanish, German, Italian, Portuguese, Simplified Chinese
-
Feel free to contact us: Mobile: 0344 3813810 Industrial plants and large facilities often have equipment and installations that draw greater than 1000 A. As with other current measurements, it is not practical to disconnect the equipment to make a series of current measurements. The ability to check that an expensive system has been installed correctly, troubleshoot large loads, and make accurate measurements on UPS and Variable Frequency drives with noisy loads is also essential. In industrial settings, compliance with NFPA 70E safety standards, while making measurements, is critical. Fluke has addressed this by designing this product to meet CAT IV 600 V and CAT III 1000 V ratings. Confidently take reliable readings with the Fluke 353 AC/DC True-rms Clamp Meter – the tool of choice for high-current clamp-on amp meter measurements up to 2000 A. The extra-wide jaw easily clamps around large conductors, typically found in high-current applications and the extra rugged design has an extra element of user protection when taking high-powered measurements. Accurate peak measurements can be taken using the in-rush current mode, ideal for motors and inductive loads. Applications: Industrial plants and facilities Building maintenance, e.g. universities, hospitals, large offices, correctional institutions Plant works, e.g. power, pharmaceutical, printing, automotive assembly Manufacturing and process facilities Refineries Steel mills and other metal manufacturing plants Large DC systems such as DC electroplating, or marine electrical systems What’s Included: Fluke C43 Soft Carrying Case 6 AA batteries Users manual 3 year warranty
-
Feel free to contact us: Mobile: 0344 3813810
- Ideal for VSDs, UPS, lighting
- AC/DC with low pass filter
- Data logging records results
- 2 Years Warranty
-
Feel free to contact us: Mobile: 0344 3813810
- Auto Power Off
- Weight 230 g (8oz)
- 2 Years Warranty
-
The Fluke 1625 is intended for electrical utility or other high frequency environments as it has extra versatility for more demanding applications. The Fluke 1625 is a distinctive earth ground tester that can perform all four types of earth ground measurement. Not only measure ground resistance using the classic ‘fall of potential test’ but also enable time saving testing using the ‘selective’ and ‘stakeless’ methods. ‘Selective’ testing does not require the electrode under test to be disconnected during the measurement, thus increasing safety. The simple ‘stakeless’ method quickly checks ground connections using two current transformers (probes) clamped around the ground conductor under test. Testing Methods
- 3- and 4-Pole Fall of Potential – standard earth ground testing using two ground stakes
- 4-Pole Soil Resistivity testing – determine soil resistivity using four ground stakes
- Selective testing – without disconnecting ground rods, a technician can measure ground resistance using a combination of stakes and a clamp.
- Stakeless testing – innovative solution using only clamps, instead of ground stakes, to measure earth ground loop resistance.
- Automatic Frequency Control (AFC) – identifies existing interference and chooses a measurement frequency to minimize its effect, providing a more accurate earth ground value.
- R* measurement – calculates earth ground impedance at 55 Hz to more accurately reflect the earth ground resistance that a fault-to-earth ground would see.
- Adjustable limits – for quick test result verification.
- Designing earth ground systems
- Installing new ground system and electrical equipment
- Periodically testing ground and lightning protection systems
- Installing large electrical equipment such as transformers, switchgears, machines, etc.
- Fluke 1625 tester
- 2 test leads
- 2 alligator clips
- 4 earth ground stakes
- 3 cable reels with wire (2-25 m, 1-50 m)
- selective/stakeless clamp set (one inducing, one sensing)
- Batteries
- Users manual
- Rugged carrying case