- Measure up to 1000 V ac and dc
- Measure up to 10 A (20 A for 30 seconds)10,000 μF capacitance range
- Frequency to 200 kHz
- Extended ac voltage bandwidth – 40 Hz to 30 kHz
- Resistance, continuity and diode test
- Min/Max and average recording to capture variations automatically
- IP 67 waterproof & dustproof protection, completely sealed for use in harsh environments
- Designed to withstand 3 meter drop (with holster)
- Average responding voltage and current for measurements (Fluke 28-II is TRMS)
- Backlit keypad buttons allow for easy visibility in lowlit areas
- Large display digits and 2 level bright white backlight for increased visibility
- Reversible holster for added protection when not in use
- Withstands hazardous 8,000 volt spikes caused by load switching and faults on industrial circuits and complies with second edition IEC and ANSI electrical safety standards
- Long battery life (800 hours)
- Relative mode to remove test lead resistance from low ohms measurements
- Auto and manual ranging for maximum flexibility
- Optional magnetic hanger for easy setup and viewing while freeing your hands for other tasks
- MSHA approval (pending)
-
Feel free to contact us: Mobile: 0344 3813810 The new standard for rugged Fluke 27 II and Fluke 28 II digital multimeters define a new standard for operating in harsh conditions with the features and accuracy to troubleshoot most electrical problems. Both meters have IP 67 (waterproof and dustproof) rating, MSHA approvals (pending), extended operating temperature range of -15 °C to +55 °C (5 °F to 131 °F, -40 °C for up to 20 minutes) and 95 % humidity, and have been designed and tested to withstand a 3 m (10 ft) drop. The new Fluke 20 Series Multimeters are built to work in the toughest environments. -
Feel free to contact us: Mobile: 0344 3813810 The Fluke 28-II multimeter is the new standard for rugged Fluke 28 II digital multimeter defines a new standard for operating in harsh conditions with the features and accuracy to troubleshoot most electrical problems. Fluke 28-II has an IP 67 (waterproof and dustproof) rating, MSHA approvals (pending), extended operating temperature range of -15 °C to +55 °C (5 °F to 131 °F, -40 °C for up to 20 minutes) and 95 % humidity, and have been designed and tested to withstand a 3 m (10 ft) drop. This meter is built to work in the toughest environments.- Measure up to 1000 V ac and dc
- Measure up to 10 A (20 A for 30 seconds)10,000 μF capacitance range
- Frequency to 200 kHz
- Extended ac voltage bandwidth – 40 Hz to 30 kHz
- Resistance, continuity and diode test
- Min/Max and average recording to capture variations automatically
- Peak min-max
- Unique function for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment
- IP 67 waterproof & dustproof protection, completely sealed for use in harsh environments
- Designed to withstand 3 meter drop (with holster)
- True-rms ac voltage and current for accurate measurements on non-linear loads
- Hi resolution 20,000 count display mode
- Backlit keypad buttons allow for easy visibility in lowlit areas
- Large display digits and 2 level bright white backlight for increased visibility
- Reversible holster for added protection when not in use
- Withstands hazardous 8,000 volt spikes caused by load switching and faults on industrial circuits and complies with second edition IEC and ANSI electrical safety standards
- Long battery life (800 hours)
- Relative mode to remove test lead resistance from low ohms measurements
- Auto and manual ranging for maximum flexibility
- Optional magnetic hanger for easy setup and viewing while freeing your hands for other tasks
- MSHA approval (pending)
-
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 The industrial meter for demanding users. New diagnostic functionality for maximizing productivity in the plant. The new Fluke 289 True-RMS Industrial Logging Multimeter with TrendCapture is the next generation high performance industrial logging multimeter designed to solve complex problems in electronics, plant automation, power distribution, and electro-mechanical equipment. With the ability to log data and review it graphically on-screen, you can solve problems faster and help minimize downtime. Let the new 289 be your watchdog for systems or processes while you are off solving other problems. Be sure to also check out the Fluke 287 True-RMS Electronics Logging Multimeter with TrendCapture designed for electronics professionals or the Fluke 289 and Fluke i400 Clamp Meter Combo Kit APPLICATIONS:- Install or maintaining electronic machinery/plant equipment
- Testing adjustable speed motor drives
- Log and record results
- In-plant automation applications
- Power distribution
- Electro-mechanical equipment service
- Industrial electronics
- Manual
- 6 AA Batteries, installed
- TL71 Silicone Test Leads
- Probe Holder
- Two AC72 Alligator Clips
- Registration Card
- Cal Practices Document
- CD-ROM Users’ Manual (16 languages)
- Getting Started Manual
- Calibration Certification Sheet
-
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 -
The Fluke 1625 is intended for electrical utility or other high frequency environments as it has extra versatility for more demanding applications. The Fluke 1625 is a distinctive earth ground tester that can perform all four types of earth ground measurement. Not only measure ground resistance using the classic ‘fall of potential test’ but also enable time saving testing using the ‘selective’ and ‘stakeless’ methods. ‘Selective’ testing does not require the electrode under test to be disconnected during the measurement, thus increasing safety. The simple ‘stakeless’ method quickly checks ground connections using two current transformers (probes) clamped around the ground conductor under test. Testing Methods- 3- and 4-Pole Fall of Potential – standard earth ground testing using two ground stakes
- 4-Pole Soil Resistivity testing – determine soil resistivity using four ground stakes
- Selective testing – without disconnecting ground rods, a technician can measure ground resistance using a combination of stakes and a clamp.
- Stakeless testing – innovative solution using only clamps, instead of ground stakes, to measure earth ground loop resistance.
- Automatic Frequency Control (AFC) – identifies existing interference and chooses a measurement frequency to minimize its effect, providing a more accurate earth ground value.
- R* measurement – calculates earth ground impedance at 55 Hz to more accurately reflect the earth ground resistance that a fault-to-earth ground would see.
- Adjustable limits – for quick test result verification.
- Designing earth ground systems
- Installing new ground system and electrical equipment
- Periodically testing ground and lightning protection systems
- Installing large electrical equipment such as transformers, switchgears, machines, etc.
- Fluke 1625 tester
- 2 test leads
- 2 alligator clips
- 4 earth ground stakes
- 3 cable reels with wire (2-25 m, 1-50 m)
- selective/stakeless clamp set (one inducing, one sensing)
- Batteries
- Users manual
- Rugged carrying case
-
Feel free to contact us: Mobile: 0344 3813810- Auto Power Off
- Weight 230 g (8oz)
- 2 Years Warranty
-
Feel free to contact us: Mobile: 0344 3813810 Industrial plants and large facilities often have equipment and installations that draw greater than 1000 A. As with other current measurements, it is not practical to disconnect the equipment to make a series of current measurements. The ability to check that an expensive system has been installed correctly, troubleshoot large loads, and make accurate measurements on UPS and Variable Frequency drives with noisy loads is also essential. In industrial settings, compliance with NFPA 70E safety standards, while making measurements, is critical. Fluke has addressed this by designing this product to meet CAT IV 600 V and CAT III 1000 V ratings. Confidently take reliable readings with the Fluke 353 AC/DC True-rms Clamp Meter – the tool of choice for high-current clamp-on amp meter measurements up to 2000 A. The extra-wide jaw easily clamps around large conductors, typically found in high-current applications and the extra rugged design has an extra element of user protection when taking high-powered measurements. Accurate peak measurements can be taken using the in-rush current mode, ideal for motors and inductive loads. Applications: Industrial plants and facilities Building maintenance, e.g. universities, hospitals, large offices, correctional institutions Plant works, e.g. power, pharmaceutical, printing, automotive assembly Manufacturing and process facilities Refineries Steel mills and other metal manufacturing plants Large DC systems such as DC electroplating, or marine electrical systems What’s Included: Fluke C43 Soft Carrying Case 6 AA batteries Users manual 3 year warranty
