-
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810- True-RMS 1000A AC/DC
- Work in tight spots with the 18" iFlex current probe and measure up to 2500A AC
- CAT III/IV Safety ratings
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810- CAT IV 600
- CAT III 1000 V
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810- True-RMS
- 600 A AC/DC
- Works with iFlex flexible current probes
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810- Detachable Jaw clamp
- Built in Flash/Torch light
- 3 years Warranty
- CAT IV 600, CAT III 1000 V
- iFlex 2500 A AC
- 1000 V AC/DC
- mV DC
- 60 kΩ
- 1000 μF
- 18-inch iFlex flexible current probe – i2500-18
- TL75 test leads
- Coated instruction card
- Safety information sheet
- Soft carrying case
- Two AA Alkaline batteries
-
Feel free to contact us: Mobile: 0344 3813810 The Fluke 360 leakage tester is a rugged and accurate solution for leakage current measurement. Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment – saving you time, without compromising on quality or safety. The unique jaw design of the Fluke 360 AC Leakage Current Clamp Meter eliminates the influence of adjacent current conductors, and measure leakage current down to 1 µA for monitoring of insulation and makes it ideal for checking insulation of low-voltage circuits and electrical components.. The ergonomic design of the Fluke 360 ensures easy measuring. The measuring clamp fits into tight spaces and the wide display angle clearly shows the measured value on the display after removing the clamp for the measured conductor. The Fluke 360 minimizes the effects of external magnetic fields, even at low currents. This allows you to perform accurate and reliable tests in today’s crowded electrical environments. The tough and high-quality jaw design of the Fluke 360 leakage tester guarantees high stability for long-term repeatability and durability. Why leakage current testing? Leakage currents can be an indicator of the effectiveness of insulation on conductors. High levels of leakage current may be present in circuits where either the insulation resistance is low, or electronic equipment with filters is used. Leakage currents can cause disruptions of the normal operation of equipment and installations. It is possible to locate the source of leakage currents by using the Fluke 360 leakage current clamp meter and taking methodical measurements throughout the installation. The big advantage of leakage current testing versus insulation testing is that the installation and equipment do not need to be powered down but can be done during normal operation. What’s Included:- Soft carrying pouch
- Users manual in languages: English, French, Spanish, German, Italian, Portuguese, Simplified Chinese
-
Feel free to contact us: Mobile: 0344 3813810 Industrial plants and large facilities often have equipment and installations that draw greater than 1000 A. As with other current measurements, it is not practical to disconnect the equipment to make a series of current measurements. The ability to check that an expensive system has been installed correctly, troubleshoot large loads, and make accurate measurements on UPS and Variable Frequency drives with noisy loads is also essential. In industrial settings, compliance with NFPA 70E safety standards, while making measurements, is critical. Fluke has addressed this by designing this product to meet CAT IV 600 V and CAT III 1000 V ratings. Confidently take reliable readings with the Fluke 353 AC/DC True-rms Clamp Meter – the tool of choice for high-current clamp-on amp meter measurements up to 2000 A. The extra-wide jaw easily clamps around large conductors, typically found in high-current applications and the extra rugged design has an extra element of user protection when taking high-powered measurements. Accurate peak measurements can be taken using the in-rush current mode, ideal for motors and inductive loads. Applications: Industrial plants and facilities Building maintenance, e.g. universities, hospitals, large offices, correctional institutions Plant works, e.g. power, pharmaceutical, printing, automotive assembly Manufacturing and process facilities Refineries Steel mills and other metal manufacturing plants Large DC systems such as DC electroplating, or marine electrical systems What’s Included: Fluke C43 Soft Carrying Case 6 AA batteries Users manual 3 year warranty -
Feel free to contact us: Mobile: 0344 3813810- Ideal for VSDs, UPS, lighting
- AC/DC with low pass filter
- Data logging records results
- 2 Years Warranty
-
Feel free to contact us: Mobile: 0344 3813810 The Fluke 345 Power Quality Clamp Meter is Fluke’s newest power quality analyzer and is an ideal meter for commissioning and troubleshooting modern electrical loads. The Fluke 345 combines a power quality analyzer, digital clamp meter, oscilloscope, and data logger in one. This combination of functions, coupled with high quality digital filtering, makes it ideal for working with variable frequency motor drives, high efficiency lighting, and other loads using switching electronics. With the bright color power meter display to analyze the harmonic spectrum, a low-pass filter to remove high frequency noise, and a high EMC immunity design, the Fluke 345 power analyzer is ideal for measurements on switching loads such as variable speed drives, electronic lighting and UPS systems. Of course, the Fluke 345 is easy to use and will make the basic measurements of voltage and current to determine if there is something seriously wrong with the circuit under test. It’s rated for use at the service entrance with a 600 Volt CAT IV rating. With the 2000 A range and large jaw opening, you can evaluate most of the circuits in the building. The Fluke 345 can also measure both ac and dc voltage and current simultaneously, and identify the magnitude of each separately and combined as ac+dc true-rms. The Fluke 345 Power Quality Clamp Meter is the ideal tool for technicians and engineer involved in installing and commission switch electronic loads. It can deal with the difficult demands of measuring and monitoring variable frequency drives, UPS systems and other switching loads. It’s simply the ideal meter for commissioning and troubleshooting modern electrical loads. Additionally, the Hall Effect measurement system design makes measurement of dc current possible without the need to break the circuit with the power meter and the internal memory enables long-term logging for analysis of trends or intermittent problems. Applications:- Setup and troubleshoot variable frequency drives and UPS systems – Verify correct operation by measuring key power quality parameters
- Harmonics measurements – Uncover harmonic issues that can damage or disrupt critical equipment
- Inrush capture – Check start-up current where spurious resets or nuisance circuit breaker tripping occurs
- Load studies – Verify electrical system capacity before adding loads
- 345 Power Quality Clamp Meter
- Soft carrying case
- Power Log software
- Test leads
- Alligator clips
- Test probes
- USB cable
- International ac adapter / battery eliminator
- Printed English language user manual
- Multi-language manual CD
-
Feel free to contact us: Mobile: 0344 3813810 he Fluke 345 Power Quality Clamp Meter is Fluke’s newest power quality analyzer and is an ideal meter for commissioning and troubleshooting modern electrical loads. The Fluke 345 combines a power quality analyzer, digital clamp meter, oscilloscope, and data logger in one. This combination of functions, coupled with high quality digital filtering, makes it ideal for working with variable frequency motor drives, high efficiency lighting, and other loads using switching electronics. With the bright color power meter display to analyze the harmonic spectrum, a low-pass filter to remove high frequency noise, and a high EMC immunity design, the Fluke 345 power analyzer is ideal for measurements on switching loads such as variable speed drives, electronic lighting and UPS systems. Of course, the Fluke 345 is easy to use and will make the basic measurements of voltage and current to determine if there is something seriously wrong with the circuit under test. It’s rated for use at the service entrance with a 600 Volt CAT IV rating. With the 2000 A range and large jaw opening, you can evaluate most of the circuits in the building. The Fluke 345 can also measure both ac and dc voltage and current simultaneously, and identify the magnitude of each separately and combined as ac+dc true-rms. The Fluke 345 Power Quality Clamp Meter is the ideal tool for technicians and engineer involved in installing and commission switch electronic loads. It can deal with the difficult demands of measuring and monitoring variable frequency drives, UPS systems and other switching loads. It’s simply the ideal meter for commissioning and troubleshooting modern electrical loads. Additionally, the Hall Effect measurement system design makes measurement of dc current possible without the need to break the circuit with the power meter and the internal memory enables long-term logging for analysis of trends or intermittent problems. Applications:- Setup and troubleshoot variable frequency drives and UPS systems – Verify correct operation by measuring key power quality parameters
- Harmonics measurements – Uncover harmonic issues that can damage or disrupt critical equipment
- Inrush capture – Check start-up current where spurious resets or nuisance circuit breaker tripping occurs
- Load studies – Verify electrical system capacity before adding loads
- 345 Power Quality Clamp Meter
- Soft carrying case
- Power Log software
- Test leads
- Alligator clips
- Test probes
- USB cable
- International ac adapter / battery eliminator
- Printed English language user manual
- Multi-language manual CD
-
Feel free to contact us: Mobile: 0344 3813810- Auto Power Off
- Weight 230 g (8oz)
- 2 Years Warranty
-
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 The industrial meter for demanding users. New diagnostic functionality for maximizing productivity in the plant. The new Fluke 289 True-RMS Industrial Logging Multimeter with TrendCapture is the next generation high performance industrial logging multimeter designed to solve complex problems in electronics, plant automation, power distribution, and electro-mechanical equipment. With the ability to log data and review it graphically on-screen, you can solve problems faster and help minimize downtime. Let the new 289 be your watchdog for systems or processes while you are off solving other problems. Be sure to also check out the Fluke 287 True-RMS Electronics Logging Multimeter with TrendCapture designed for electronics professionals or the Fluke 289 and Fluke i400 Clamp Meter Combo Kit APPLICATIONS:- Install or maintaining electronic machinery/plant equipment
- Testing adjustable speed motor drives
- Log and record results
- In-plant automation applications
- Power distribution
- Electro-mechanical equipment service
- Industrial electronics
- Manual
- 6 AA Batteries, installed
- TL71 Silicone Test Leads
- Probe Holder
- Two AC72 Alligator Clips
- Registration Card
- Cal Practices Document
- CD-ROM Users’ Manual (16 languages)
- Getting Started Manual
- Calibration Certification Sheet
-
Feel free to contact us: Mobile: 0344 3813810 -
Feel free to contact us: Mobile: 0344 3813810 The Fluke 287 True-rms Electronics Logging Multimeter with TrendCapture quickly documents design performance and graphically displays what happened. Its’ unique logging and graphing capabilities mean you no longer need to download logged readings to a PC to detect a trend. The Fluke 287 True-rms Electronics Logging Multimeter with TrendCapture packs more accuracy and convenience into a handheld multimeter than ever before, putting more problem solving power in your hands. It is the ultimate handheld tool for demanding applications that require high-precision APPLICATIONS:- Develop, install, or maintain electronic devices
- Precision testing of surface mount and high density circuits
- Customers who need to log and record results to solve intermittent problems
- Communication; wireless, wired, LAN, broadband, CATV, audio/video
- Industrial / Electrical equipment
- Instrumentation (example: test and medical equipment)
- Consumer electronics
- Automotive
- Education
- Security
- Manual
- 6 AA Batteries, installed
- TL71 Silicone Test Leads
- Probe Holder
- Two AC72 Alligator Clips
- Registration Card
- Cal Practices Document
- CD-ROM Users’ Manual (16 languages)
- Getting Started Manual
- Calibration Certification Sheet
Call Us Today! (+92 307-7381381, +92 321-1818381) | buysolarpakistan@gmail.com
